There will come a point in time when your water heater tank will stop performing with the same efficiency that it used to perform when you had initially bought it. When that time comes, there is no point shelling out money to repair it, the best option will be to replace it.

Of course, you can install a water heater tank all by yourself if you have the knowledge and if you are confident. But if you have even the slightest doubt then call a water heater installation professional or a plumbing expert to do the job.

Installation of a water heater tank will begin only after you have purchased the water heater model that you want.

How to Install a Water Heater Tank

One of the important things to remember before you start with the installation of a water heater tank is that you need to read the entire installation manual, which comes with the heater. The installation manual will provide you important information regarding each and every part of the heater and how to connect the wirings, piping etc.

Step#1: You need to ideally set up the new water heater tank in the same place as the older one was fitted. Normally, the best place to fit a tank is in the basement.

Step#2: You need to first turn off all the utilities connected to the previous water heater tank. Some of the important things that you need to do include:
•    Turning off the water using the main water shut-off valve
•    Shut off the electricity if you are going to install an electric water heater tank
•    Turn off the gas if you are going to install gas water heater tank

Step#3: This is an important step and involves removal and replacement of the water heater tank. You will need an assistant to help you in removing the old tank and putting the new tank in its place. Once you have removed the old tank, clean the floor under the tank. Move the new tank into the right position. It should line up perfectly with the existing plumbing system. Now use a torpedo level to help you in leveling the new water heater tank.

Step#4
: The next step is to install the various fittings that come with the water heater tank. At this point you should check the installation manual to see if you are securing the fittings correctly and in the right place. Some of the steps you need to follow include:

•    Installing the pressure and temperature and relief valve as well as the discharge drain pipe.
•    It is recommended to use Teflon tape on copper and galvanized fittings.
•    Install each fitting one at a time as per the manufacturer’s instructions.

Step#5: The next step is to connect the hot and cold water lines and this is called “installation of the plumbing lines”. Some of aspects that you need to consider include:

•    You need to use flexible copper supply lines in case the tank’s inlet and outlet openings are not lining up at the exact point of the old plumbing.
•    You need to add a shut-off valve for the cold water supply if it is inexistent.
•    Use dielectric unions for connecting the pipes. This will help in preventing any electro-galvanic action like electrolysis. Electrolysis can cause serious damage to your water heater as well as the pipe connections.
•    It is recommended to use Teflon tape on threaded copper and joint compounds for galvanized fittings.

Step#6: Now connect the electric or the gas lines depending on the type of water heater tank you are installing. Here are some aspects to consider and steps to follow:

•    The gas line needs to be connected to the gas burner control valve. If required, use a flexible gas line.
•    Always make it a point to check for any leaks. You can conduct the check by turning on the gas supply valve and brushing it with soap water solution. If there is a leak, you will see bubbles. Use a strong and good sealant to cover the leak permanently.
•    If you are installing an electric water heater then you have to connect the power lines and ground wire to the junction box of the heater.
•    If you have a gas model then connect the exhaust flue.

Now all you have to do is turn on the water heater tank!

Back from Tank to Water Heater Installation

Back from Water Heater Tank to Hot-Water.com

Heater Tank

There will come a point in time when your water heater tank will stop performing with the same efficiency that it used to perform when you had initially bought it. When that time comes, there is no point shelling out money to repair it, the best option will be to replace it.

Of course, you can install a water heater tank all by yourself if you have the knowledge and if you are confident. But if you have even the slightest doubt then call a water heater installation professional or a plumbing expert to do the job.

Installation of a water heater tank will begin only after you have purchased the water heater model that you want.

How to Install a Water Heater Tank

One of the important things to remember before you start with the installation of a water heater tank is that you need to read the entire installation manual, which comes with the heater. The installation manual will provide you important information regarding each and every part of the heater and how to connect the wirings, piping etc.

Step#1: You need to ideally set up the new water heater tank in the same place as the older one was fitted. Normally, the best place to fit a tank is in the basement.

Step#2: You need to first turn off all the utilities connected to the previous water heater tank. Some of the important things that you need to do include:

· Turning off the water using the main water shut-off valve

· Shut off the electricity if you are going to install an electric water heater tank

· Turn off the gas if you are going to install gas water heater tank

Step#3: This is an important step and involves removal and replacement of the water heater tank. You will need an assistant to help you in removing the old tank and putting the new tank in its place. Once you have removed the old tank, clean the floor under the tank. Move the new tank into the right position. It should line up perfectly with the existing plumbing system. Now use a torpedo level to help you in leveling the new water heater tank.

Step#4: The next step is to install the various fittings that come with the water heater tank. At this point you should check the installation manual to see if you are securing the fittings correctly and in the right place. Some of the steps you need to follow include:

· Installing the pressure and temperature and relief valve as well as the discharge drain pipe.

· It is recommended to use Teflon tape on copper and galvanized fittings.

· Install each fitting one at a time as per the manufacturer’s instructions.

Step#5: The next step is to connect the hot and cold water lines and this is called “installation of the plumbing lines”. Some of aspects that you need to consider include:

· You need to use flexible copper supply lines in case the tank’s inlet and outlet openings are not lining up at the exact point of the old plumbing.

· You need to add a shut-off valve for the cold water supply if it is inexistent.

· Use dielectric unions for connecting the pipes. This will help in preventing any electro-galvanic action like electrolysis. Electrolysis can cause serious damage to your water heater as well as the pipe connections.

· It is recommended to use Teflon tape on threaded copper and joint compounds for galvanized fittings.

Step#6: Now connect the electric or the gas lines depending on the type of water heater tank you are installing. Here are some aspects to consider and steps to follow:

· The gas line needs to be connected to the gas burner control valve. If required, use a flexible gas line.

· Always make it a point to check for any leaks. You can conduct the check by turning on the gas supply valve and brushing it with soap water solution. If there is a leak, you will see bubbles. Use a strong and good sealant to cover the leak permanently.

· If you are installing an electric water heater then you have to connect the power lines and ground wire to the junction box of the heater.

· If you have a gas model then connect the exhaust flue

Now all you have to do is turn on the water heater tank!

Related Posts

Tankless Water Heater Tax Credit And Rebate Did you know that the U.S. Government offers a tax credit and/or rebate for those who switch out their water heaters to new, energy-efficient models? If you're looking for a way to deduct a bit fro...
Water Heater Elements It’s safe to assume that almost every household in the U.S. has at least one water heater. Now more often than not, water heaters need to be maintained and one of the most important parts that need to...
Water Heater Thermocouple If you own a gas water heater then you have probably experienced a water heater thermocouple failure. Are you wondering what a water heater thermocouple really is? Basically, more often than not, you ...

Leave a Reply